Versions-History 8400 StateLine frequency inverters

Version V21.02.00.0000

• not existing

• Timeout with empty "retain memory" / Error message "dF50"

• not existing

Version V21.01.00.0000

• not existing

• Increasing the value range of C12 and C13
• Data consistency in the external serial flash

Version V21.00.00.0000

• Initialising the brake resistor utilisation
• Automatic oscilloscope start after mains connection
• Optimising SLPSM control

• No connection via remote maintenance router
• Auto-start lock after undervoltage error
• Sporadic error message DF21 (BU watchdog)
• Error when loading the parameters from copied memory modules

Version V20.00.00.0000

• New memory modules supported

• "L_Compare_X"and "L_ComparePhi_X" with input value 0x8000 or 0x80000000

Version V18.00.00.0000

• Load default setting without communication parameters
• Extension of initial keypad screen
• Torque limitation with HighLimit and LowLimit possible

• Motor stalling with SLVC and high output frequency
• Error message dF25 (CU RCOM) with PPI without movement
• Delayed start of Ethernet Powerlink control nodes (slaves)

Version V17.00.00.0000

• not existing

• not existing

Version V16.02.00.0000

• not existing

• not existing

Version V16.01.00.0000

• not existing

• Incorrect triggering of An01: AIN1_I < 4 mA or An02: AIN2_I < 4 mA

Version V16.00.00.0000

• L_DigitalLogic: 2 additional logic functions
• LS_ParReadWrite: Read value remains optionally pending
• Overcurrent monitoring (overload monitoring) OC18
• Device can transmit process data with individual sync
• Hysteresis for nact detection can be set under code C0025/1
• Elapsed-hour meter and power-on time meter are always displayed in case of 24-V supply
• Optimisation of the motor phase failure monitoring function
• Lower limit of C091 (motor cosine phi) has been adapted
• Slip compensation for VFCplus does not work after downloading parameters
• Display: Speed limitation reached
• Display code C920/x 'Rated current' and 'Increased rated current'
• V/f emergency operation in case of open circuit of HTL encoder
• Additional error messages of reaction type 'Information'

• No PS03 info when replacing memory module with compatible parameter sets
• Oscilloscope does not trigger in the case of digital signals and "Value change" trigger mode.
• Flying restart circuit does not work in the event of a short-time undervoltage
• Rated device currents are slightly too low
• SLPSM: Current fluctuations in the controlled range
• Vibrations with SLPSM if fdmax=C59 is higher than 650Hz

Version V15.01.00.0000

• Automatic switch-over to V/f without encoder as emergency operation
• Installation of CAN PDO 4

• User LED is working with "Optical tracking"
• MCK setpoints not increment-precise in the case of QSP

Version V14.00.00.0000

• Extension of the Id8 error message: speed sensor not set
• Extension of the dH70 error message: ControlUnit does not comply with BaseUnit
• Extension of the brake chopper control
• Parameter set transfer with the keypad
• Entry of texts in the keypad
• Display of bit texts in the keypad.
• New error tripping with regard to pole position identification
• Increase of the maximum current limit at a fixed switching frequency of 4kHz for a power of 30kW, 37kW, and 45kW
• Motor parameter identification at switching frequency of 8kHz
• 1.1.3. Extension of the process display for the active output current and apparent output current
• SLPSM for application reference frequency C59 > 650Hz
• Transferring the CAN address switch to MCI module

• SC-PSM jitters at high output speeds (> approx. 700Hz)
• Profinet station name cannot be written
• Id7 error in the case of a parameter set changeover with a definable list
• Operation of an asynchronous machine with a very high slip speed not possible
• No pulse inhibit after expiry of the hold time set for the manual DC injection brake with C142= 0
• SLVC: OC1/OC11 error if fd>650Hz
• VFC: Slip compensation at fd>650Hz
• Torque accuracy if no KTY is available
• SLVC/VFC: Apparent current display C054 jitters at f = 0 Hz
• "Reset error" of a short circuit disconnection (OC1)
• Speed step change after switching on the BaseUnit
• After the parameter change-over (LS_WriteParamList), the motor does not run correctly
• Profinet station name cannot be written
• Operation with fout ≥ 650Hz causes OC11 error
• Following error is deleted at controller inhibit
• M-feedforward control unstable if the sensitivity of setpoint feedforward control is ≤12 bits

Version V13.00.00.0000

• Additional process input bVfcEcoDisable
• Additional process output bLimSpeedTorquemodeOn
• Additional process output nVoltageAngleAct
• Display parameter C162/1 for subject area +Id of the current error menu
• AC drive profiles speed and speed and torque actuation with EtherNet/IP™

• Incorrect scaling of the speed controller parameters if C059≥650Hz
• No keypad texts for bit codes
• Current dips at fswitch
• Sporadic motor phase error before operation
• C002 reports 'OFF/complete‘ in spite of Id4 error during motor parameter identification
• Switching hysteresis for device fan too low
• In the case of download, C653/1 is overwritten with the value from C2314/1
• Incorrect display of the interior temperature CU C062
• Not all parameters selected in C517 can be viewed in the keypad user menu.
• Unexpected rotating direction at start of PC manual control
• Process setpoint interfaces in spite of operation via PC manual control
• Ethernet Powerlink synchronisation not possible
• Quantisation of the M-feedforward control with a correlation of J and t_acc
• Torque limitation takes effect in the case of QSP
• Brake chopper threshold is not adapted depending on C173

Version V12.00.00.0000

• Support of EtherNet-IP fieldbus modules
• Counter for STO, DigIn CINH, and IMP after mains connection
• Automatic calculation of the current and field controller parameters
• Speed limitation to 0rpm if bTorqueModeOn=TRUE
• Torque limitation for bTorqueModeOn=TRUE
• Starting value C122 for motor overload according to U_L and U_R specification
• Automatic detection SM or ASM from motor parameters
• Extension of the position encoder selection C490
• Parallel control of brake choppers in DC-bus connection
• CAN gateway for forwarding SDO requests via MCI
• Adjustable delay time for IMax status
• Extension of C199 to 5x32 bytes for device identification
• Logbook read interface for the control or HMI
• User level keypad selectable in C001
• Extension of the acceleration feedforward control
• Oscilloscope function
• LS_WriteParList ? change-over of motor parameters in 2ms

• Untrue running of power loss-optimised modulation modes (Eliminated from FW 12.00)
• Function of the inversion of motor phase rotating direction only for V/f (Eliminated from FW 12.00)
• Jerk during the deactivation of DC-injection braking at n_act ≠0 (Eliminated from FW 12.00)
• Application of n_act ≠0 in SC-ASM control mode is not compensated (Eliminated from FW 12.00)
• Brake chopper threshold, LU-threshold, and DC-voltage incorrect in the case of 230 V devices (Eliminated from FW 12.00)
• Overcurrent during the transition from open-loop operation to closed-loop controlled operation SLPSM (Eliminated from FW 12.00)
• Oscillation tendency in the case of a very dynamic setpoint change in SLVC (Eliminated from FW 12.00)
• OC1 error after enable in the case of SM with a low inductance (Eliminated from FW 12.00)
• Sporadic OC13 error during DC-injection braking (Eliminated from FW 12.00)
• Flying restart process in SLVC after change-over of the control mode without function (Eliminated from FW 12.00)
• Setpoint current in SLPSM cannot be preselected higher than 328 % (Eliminated from FW 12.00)
• SU03 error in the case of DC supply (Eliminated from FW 12.00)
• Fixed 3 ms PT1 filtering in the analog inputs 1+2 (Eliminated from FW 12.00)

Version 1D

• not existing

• not existing

• not existing