Versions-History Controller c500

Version V01.14.00.0000

• not existing

• No access to the file system of the USB stick inserted in the controller (fixed from V1.14)

• EtherCAT does not switch to 'Operational'
• EtherCAT master: 'SlaveAutoRestart' parameter has no effect
• Controller does not start (RDY LED flashes)
• Incorrect process data in the input image
• No PROFINET communication after download in Siemens controller
• Controller with EtherCAT HotConnect: Exception at ETCSlave.HcGroup.Name when HC node is copied
• When executing online change, the message "Download failed: Unknown reason" appears
• Ports < 1024 cannot be opened
• OPC UA access rights not backwards compatible
• WKC error every time EtherCAT is started if IO3000 is connected
• CoDeSys WebServer (controller version 'Extended') does not work with https
• Controller is delivered with expired certificates
• Persistent variables have their default values again after restarting the controller
• Profinet: Alarm suppression does not support all error responses
• OPC UA Client cannot connect via the server hostname.
• Error message 'Connection denied by device: All available communication channels are already in use'
• Visu via ARTI3 no longer works after update to V1.11
• L_IE1P_ReadActualtSeverity: FB does not display the warning of a drive
• Outgoing Ethernet connections, e.g. OPC-UA Client, from the controller are not established when the firewall is active.
• Diagnosis Visu does not work after firmware downgrade
• L_Util_Retain causes unclear error messages
• c5x0 - No consistent data transmission to the PLC task via OPC-UA (No change planned)
• Error message "No access-parameter set was not saved"
• Parameter of type STRING shows no more than 81 characters
• FAST UI Runtime - Start page: Projects are not listed if HTTPS Redirect Enabled
• User administration: Password cannot be changed
• Vulnerability in OPC-UA authentication
• Controller c520, c550: Increase in cycle time
• No secure real-time processing of tasks with a priority greater than 15
• OPC UA Server does not display PLCopen information model
• c5x0 / c750: Profinet: sporadically the station name is lost after power switching
• Retain variables or logbooks are not stored sporadically.
• SD cards of a certain serial number range are not suited for i950 / c5x0 / c750 (no remedy possible)

Version V01.13.00.0000

• OPC UA client - supports "browsing"
• OPC UA - File Access (write, delete, rename,..)
• OPC UA Security - GDS (Global Discovery Server)
• OPC UA Security - SKS (Security Key Service) with PubSub
• Cyber Security: USB stick is not mounted automatically
• c4xx, c5xx: SysLog (System Logging Protocol) is supported
• EtherCAT: Support for hot connect groups
• Multiple parameter sets for one EtherCAT device
• Cyber security: configurable password policy

• Controller with Profinet: PDO data is not sent from the controller to Siemens PLC (fixed from V1.13.0)
• Alarms: AlarmList does not display any LEM alarms until Diagnostic-Visu is started in parallel
• Controller not found after activation of encrypted communication
• Network variables are sporadically not updated (fixed with V1.13)
• PROFINET process data communication does not work (fixed with V1.13)
• L_IPAP_ParameterWrite: Error message when writing parameters of type 'String' (fixed with V1.13)
• After restarting the OPC UA server, parameters in the PLC Designer remain "red"
• No encrypted communication possible between PLC Designer and controller via PROFINET interface (fixed with V1.13)
• Boot application cannot be created after 'Reset origin device' (fixed with V1.13)
• FAST UI Runtime: After an online change from the PLC Designer no more values can be written from the WebClient

Version V01.12.00.0000

• Trend system
• NTP Server

• Values of the EPM-S6xx IO modules on the controller's backplane bus are not displayed in PLC Designer (fixed as of V1.13.0)
• FAST UI Runtime - Project Start: ServerProjectStartTimeout without effect

Version V01.11.00.0000

• FAST UI Runtime: New project startup page
• FAST UI Runtime: Secure communication
• FAST UI Runtime: Input via physical keyboard into touch keyboard
• FAST UI Runtime: system variables (language, page, user) are available
• FAST UI Runtime: Show loading symbol
• Lenze Component Directory: Recording data on components used
• Diagnostics visualization: Overview display of the application credit
• FAST UI Runtime: Acknowledge all alarms action
• OPC UA client / security: encrypted communication with the exchange of certificates

• Boot application with encrypted application not possible
• Runtime - Historical AlarmList: Historical alarms are displayed unsorted.
• FAST UI Runtime - Historical Alarms: Status "InactiveAck" is not displayed.
• Runtime - Historical Alarms: Duplicate entries for the "cleared" status
• PLC application does not start when the controller is started due to a corrupt log file
• EtherCAT master is not automatically updated with the controller
• Recipe management: error message when loading recipes from device
• c5xx: EPM-S310 on the backplane bus do not work if an EtherCAT or Profinet fieldbus module is plugged in
• No login possible if the device name is too long
• Message: PLCParameterManager - Initialization: 0x2001.0 parameter value could not be written
• PROFINET: Complete communication failure due to excessive ARP request burst load

Version V01.10.03.0000

• not existing

• Diagnostic and process visualization: Alarms are not displayed or cannot be acknowledged

Version V01.10.00.0000

• OPC UA Server Diagnostics & Settings dialogs available

• When user administration is switched on, the task runtime increases briefly (corrected from V1.10)
• EtherCAT device interface does not adopt the second slave address (corrected from V1.10)
• PLC exception error when passing an Axis_REF to a function (corrected from V1.10)

Version V01.09.00.0000

• Lenze License Manager - FAST licensing as a service in the controller
• LENZE OPC UA: Methods; Events; Clients; License
• Web Diagnosis: Login dialogue

• Parameter sets of the devices connected to the controller are not stored in a power-failure-proof manner (corrected from V1.9)
• MMC: Bits "IsPresent" and "IsMandatory" without function in the c250-S (corrected from V1.9)
• Outputs are not set to default values after exception (corrected from V1.9)
• After a device exchange of an EtherCAT slave, the EtherCAT is not operational. (corrected from V3.21.3 / V1.9)
• Persistent variables have default values (corrected from V1.9)
• Error message 'PLL Error' when starting up the EtherCAT (corrected from V1.9)
• Boot application is deleted after exception (corrected)
• External control reports invalid process data - Profinet does not start sporadically (corrected from V1.9)
• L_ETC_ReadErrCnt2: EtherCAT fault is not displayed (corrected from V3.26)

Version V01.08.01.0000

• not existing

• not existing

Version V01.08.00.0000

• not existing

• OPC UA Server: error message "BadTooManySubscriptions" (fixed to V1.8)
• OPC UA server no longer addressable when address range is browsed
• OPC-UA Server reports out of memory due to many files on the SD card
• PROFINET: Bitwise transmission fails (corrected from V1.8)

Version V01.07.00.0000

• Lenze OPC UA Server with c5x0 and c750
• Improved EtherCAT diagnostics
• Support of the Lenze EtherCAT Device
• Support of secure communication for web-visu
• FAST_System_Diagnosis' object
• FAST_System_Configuration' object
• Object 'ParameterEditor'
• FAST Toolbox becomes FAST Framework (Step 1)

• IO-1000: Error messages when translating the PLC project
• Task configuration - Monitoring: Element jitter does not show instantaneous value (behoben ab V1.7)
• Error messages when connecting with OPC UA Expert (corrected from V1.7)
• Backplane bus of the controller not running (corrected from V1.7)
• Task configuration: Display of a too large jitter value (corrected from V1.7)
• After download or reset cold no data exchange via EtherCAT device (corrected from V1.7)
• Error message 'Network: Invalid configuration'.

Version V01.06.02.0000

• not existing

• not existing

Version V01.06.01.0000

• not existing

• not existing

Version V01.06.00.0000

• not existing

• PLC logbook contains debugging information (fixed from V1.6)
• Function call of 'SysTargetGet...' overwrites application memory (corrected from V1.6)

Version V01.05.00.0000

• Configuration of the automatic firmware update of EtherCAT slaves
• Firmware download via Ethernet
• EASY Starter supports Lenze controllers c5xx and c750
• Ethernet Tunnel via Profinet Interface
• OPC-UA: Changed data type when accessing TIME variables

• Profinet communication aborts when using the i950 engineering port at the same time (corrected from V01.05.00)
• c5x0 / c750: PLC Designer communication can sporadically not be established to the device after parameter change (fixed from V1.5)
• Parameter sets are not transferred to controller (fixed from V1.5)
• Parameter sets of the devices connected to the controller are not stored in a power-failure-proof manner (fixed as of EASY Starter V1.19 and c5xx V1.5)
• Retain variables are set to initial values by device command 0x2022/43 (fixed as of V1.5)
• c5x0 / c750: After setting the Profinet IP address, the controller can no longer be reached via Ethernet (corrected from V1.5.0)
• Fields on parameter dialogues do not change colour online and do not show correct values (fixed from V1.5, V3.20)
• IP address is not taken over when device is replaced (corrected from V1.5)
• EtherCAT bus becomes operational, although parameters could not be written during the initialization phase (corrected)
• Compiler error "C0330: Structured exception handling is not supported by your current target." (corrected from V1.5)

Version V01.04.00.0000

• not existing

• L_ETC_GetMasterDiagnostic: Output xNotAllSlavesOperational becomes not TRUE (fixed with V1.4)

Version V01.03.00.0000

• New parameters
• Device search for controller backplane bus
• Parallel parameter set download
• i550: Parameter set download if required

• Controller time is not distributed via DC (fixed as of V1.3)
• Trace recording does not start automatically after a restart (corrected from c5xx V01.03.00 and i950 FW from V01.04.01)
• Power-fail-safe data are reset after SD card exchange (fixed from V1.3)
• EtherCAT bus is not operational (fixed from V1.3)

Version V01.02.00.0000

• not existing

• PROFINET PROFIdrive multi-parameter access: only 32 instead of 40 parameters simultaneously (fixed from V01.02)