Versions-History L_TS2P_TechModulesSynchronizingCamming

Version V03.33.00.0000

• not existing

• L_TS2P_ElectronicGearboxBase: scPar.xLoadOffset has no effect (fixed from V3.33.0)
• L_TS2P_FlexCamState: Cam switching in limited measuring system fails (fixed as of V3.33.0)

• L_TS2P_ElectronicGearbox: xSynchronised remains TRUE even though engagement was not requested
• L_TS2P_Crosscutter: Cannot change scPar.lrSensorToolDistance during cutting
• L_TS2P_FlexCAM: The y-axis expansion/compression factor lrSetScalingSlave is factored into scPar.lrSyncVel
• L_TS2P_ElectronicGearboxBase: scPar.xLoadOffset has no effect
• L_TS2P_SyncPosBase: Internal overflow when using scPar.dwGearingNumerator:=100000000
• L_TS2P_SyncAndCorrection: Limitation of the marker error
• L_TT1P_FlexCAM, L_TS2P_FlexCam: Slave reverses during disengagement
• L_TS2P_FlexCam: setting eAllowDirection = both has no function

Version V03.32.00.0000

• not existing

• L_TS2P_SyncAndCorrection: TM remains in xSynchronised status, although xEnableOperation = FALSE is set (corrected from V3.32.0)
• Faulty status message with active STO (corrected from V3.32.0)
• All TMs with clutch function: clutch can be engaged to absolute position without a reference position having been set beforehand (fixed from V3.32.0)

Version V03.31.01.0000

• not existing

• L_TS2P_CrossCutter: Error when engaging from the park position (fixed as of V3.31.1)
• L_TS2P_CrossCutter: "MasterOutOfCam" error (22025) during touch probe after trimming (fixed as of V3.31.1)

Version V03.30.00.0000

• Signing of Lenze libraries

• All TM V2: eTMState does not switch to STANDBY after HOMING (fixed from V3.30.0)
• L_TS2P_CrossCutter: Status xTrimActive invalid (fixed from V3.30.0)
• L_TS2P_FlexCamState: Error message "InvalidMasterAxisRef" at SyncIn with QSPApplication (fixed as of V3.30.0)
• All TM V2: Not all parameters from scPar are offered in the variable selection list (fixed as of V03.30.00)
• L_TS2P_ElectronicGearboxBase: Error in the accuracy of the gearbox lock (unit coupling) (Corrected from V3.30.0)
• L_TS2P_CrossCutter: CrossCutter does not restart after an SS1 (fixed from V3.30.0)

Version V03.29.00.0000

• not existing

• L_TS2P_FlexCAMState: If a Y-offset is used, the drive is moved to an incorrect disengagement position. (Corrected from V3.29.0)
• L_TS2P_SyncAndCorrection: The correction of the gear factor is frozen (corrected from V3.29.0)

Version V03.26.00.0000

• New TM: L_TS2P_SyncPos
• New TM: L_TS2P_FlyingSaw
• L_TS2P_SyncAndCorrection: Changed disengagement behaviour with limited axes

• All TM V2: QSPApplication input does not work with active "Internal Control" (corrected from V3.26.0)
• L_TS2P_FlyingSaw: Increase in CPU utilization compared to V03.24.0 (no change planned)
• L_TS2P_SyncAndCorrection: The technology module reports an Invalid input data error (corrected V3.26.0)
• L_TS2P_FlyingSawState: Wrong synchronisation ramps are used during the clutch phase (corrected from V3.26.0)
• L_TS2P_FlyingSaw: xSyncInInstant does not work correctly after switching on again (corrected from V3.26.0)
• L_TS2P_FlexCamState: Jump in the axis target acceleration at xCamChangeInstant (corrected from V3.26.0)
• L_TS2P_SyncAndCorrection: Jump during clutch engagement (corrected from V3.26)
• L_TS2P_SyncAndCorrection: xGearFactorCorr does not behave as described (corrected from V3.26.0)
• L_TS2P_FlyingSawState: Engaging after abort by QSPAppl is no longer possible (corrected from V3.26.0)
• L_TS2P_FlyingSawState: If the engagement/disengagement process is aborted by Abort, the axle performs a speed jump (corrected from V3.26.0)
• L_TS2P_FlexCamState: Output wActiveCamTable becomes 0 (corrected from V3.26.0)
• L_TS2P_FlexCamState: xSetScalingX - Unhandled exception error when changing from 0 to 1 (corrected from V3.26.0)
• L_TS2P_FlexCamState: lrSetScalingX - change from 0 to 1 does not start the movement (corrected from V3.26.0)
• L_TS2P_FlyingSawState: ResumeTargetPos does not work in marker-controlled mode (corrected from V3.26.0)
• L_TS2P_FlyingSawState: Parking position outside the working area (corrected from V3.26.0)
• FAST TM: Note for using Technology Modules V2 is wrong (corrected from V3.26)

Version V03.25.00.0000

• not existing

• L_TS2P_SyncAndCorrection: Delay with lrSyncInDist instead of lrSyncOutDist (corrected from V3.25.0)
• L_TS2P_SyncAndCorrection: Status of TM when attempting to drive in blocked direction (corrected from V3.25.0)
• All TMs from L_TS2P: Position jump when xHalt and xSync are set simultaneously (corrected from V3.25.0)
• All TMs from L_TS2P: Position jump when xAbort and xSync are set simultaneously (corrected from V3.25.0)
• L_TS2P_SyncAndCorrection: Drive overruns with negative offset corrections (corrected from V3.25.0)

Version V03.24.00.0000

• not existing

• L_TS2P_FlyingSaw: xSyncInstant does not work with marker cut (corrected form V3.24.0)
• L_TS2P_SyncAndCorrection: The TM hangs on negative mark correction (corrected from V3.24.0)
• L_TS2P_FlyingSawState: eFlyingSawStopMode = Halt (corrected from V3.24.0)
• L_TS2P_SyncAndCorrection: Mark error detection not correct for touch probe within correction window (corrected from V3.24.0)
• L_TS2P_SyncAndCorrection: Position jump at scPar.xCalcMarkError (corrected from V3.24.0)
• L_TS2P_FlexCamState: Incorrect start synchronisation with lrJerk not equal to lrSyncJerk (corrected from V3.24.0)
• Abort function: The deceleration ramp is not as expected (corrected from V3.24.0)
• L_TS2P_SyncAndCorrection: Switching marker correction on/off causes discontinuities (corrected from V3.24.0)
• L_TS2P_CrossCutterState: Error message MasterOutOfCam (eErrorID = 22025)(corrected from V3.24.0)
• L_TS2P_FlexCamState: TM displays the wrong status during deceleration (corrected from V3.24.0)

Version V03.23.00.0000

• Technology modules V2 can now also be used on the controller 3200C, p500 and c300

• L_TT1P_FlexCAM, L_TS2P_FlexCam: Changed cam disk is not processed in the next cycle (no change planned)
• SyncAndCorrection: Error in dimension system adjustment-->X/Y (fixed as of V3.23.0)
• L_TS2P_SyncAndCorrection: No warning if tool offset is activated and TP mapping is missing (corrected from V3.24.0)
• L_TS2P_SyncAndCorrection: No warning appears after failure of the maximum allowed marks (ToolCorrection) (fixed as of V3.23.0)

Version V03.22.00.0000

• not existing

• Active limitation not diagnosable by means of eTMState = EXTERNAL (fixed from V3.22.00)
• TM ElectronicGearbox / SyncAndCorrection: The parameter eAllowedDirection has no effect on the function "BaseVelocity" (fixed from V3.22.0)
• L_TS2P: The offset procedure is not executed under certain conditions (corrected from V3.22.0)
• L_TS2P_FlexCamState, L_TS2P_SyncAndCorrection: The outputs eTMState, xWarning, eErrorID toggle their state (corrected from V3.22.0)

Version V03.21.00.0000

• Function extensions Technology module libraries V2 (V03.21.00)

• TM SyncAndCorrection: Basic speed in not allowed direction (Fixed as of V3.21.0)
• L_TS2P_ElectronicGearBase: "Application error" after limiter request (corrected from V3.21.0)
• L_TS2P_ElectronicGearbox: eAllowedDirection does not affect the engagement direction (fixed as of V3.21.0)
• L_TS2P_SyncAndCorrection: The reference value drifts with activated conductance correction (fixed as of V3.21.0)
• L_TS2P_ElectronicGearboxBase: Visualization template cannot be used (fixed as of V3.21.0)

Version V03.20.00.0000

• Function extensions Technology module libraries V2 (V03.20.00)

• Some technology modules do not book the correct number of credits (fixed from V3.20.0)
• L_TS2P_ElectronicGearboxBase: Error during limiter request SafeDirectionPostitive (negative) (fixed from V3.20.0)
• L_TS2P_CrossCutterState: CrossCutter no longer starts after canceling a limiter command (fixed from V3.20.0)
• TA Sync And Correction: Offset is not switched through/extended (eliminated from V03.20.00; V01.04.01)
• i950 TM and TA ElectronicGearbox: status signal toggles (fixed from V0.20.0; V01.04.01
• L_TS2P_SyncAndCorrection: Change of the gear factor correction leads to speed jumps (fixed since V3.20.0)
• TM SyncAndCorrection: Reaktion der Kupplung auf STO, SS1, SS2 nicht implementiert (eliminated from V3.20.0)

Version V03.19.00.0000

• L_TS2P_FlexCamState: Attack point AP_xCalcCamProfiler
• Function extensions Technology module libraries V2 (V03.19.00)

• Technology modules V2: behavior of xHalt changed (corrected from V03.19.00)